Investigation on the changes effected by tool profile on mechanical and tribological properties of friction stir processed AZ31B magnesium alloy

The present study investigates the effect of tool shoulder profile on the mechanical and tribological properties of friction stir processed AZ31B magnesium alloy. The tool rotational speed and feed rate are the chosen process parameters. The experiments were conducted with 3 level 2 factors full factorial design. The recorded responses were tensile strength, wear losses and corrosion rate. The results were analyzed with the help microstructures of the processed samples. The study reveals that, for concave shoulder tool, the strain hardening effect was playing a major role in determining the properties of the processed materials and for the step shoulder tool, the grain size plays a major role in determining the properties of the processed materials.     

LD2铝合金腐蚀行为研究

LD2铝合金广泛应用于直升机结构中。铝合金构件在服役过程中会承受环境所造成的疲劳损伤,从而大大降低其服役寿命,因此必须要研究该材料的腐蚀行为。利用SEM扫描电镜,结合能谱分析对铝合金腐蚀损伤行为进行了高精度微尺度研究,并在疲劳断口上发现腐蚀坑底部的“隧道”,该腐蚀隧道会使腐蚀损伤评定过于保守,为结构寿命预测带来较大的不确定性。     

氧气热处理的TiO2纳米管阵列光电催化降解亚甲基蓝的研究

采用原位阳极氧化法在Ti基底上制备了高度有序的TiO2纳米管阵列薄膜,SEM图像表明TiO2纳米管定向排列整齐,分布均匀,其管径范围在70～100 nm.XRD结果证明,阳极氧化法制备的TiO2纳米管为无定型晶型,经退火后为具有良好光催化活性的锐钛矿型.以亚甲基蓝（methylene blue）为目标物研究了TiO2纳米管光电催化性能及影响因素,结果表明,以0.1 mol/L NaCl为电解质,在氧气热处理气氛下,外加偏压为0.5 V、pH=3.25、光照强度为1 000μW/cm2、纳米管薄膜表面积为2 cm×2 cm且MB初始浓度为10 mg/L的条件下,TiO2纳米管阵列薄膜光电催化降解MB的降解效率可达99.56%.电化学阻抗谱分析显示,光电催化降解过程的速控步骤均为表面反应步骤,外加偏压减小了界面电荷转移阻抗,提高了光生载流子的分离效率.     

添加H2O2加速低合金钢海水腐蚀的主要影响因素研究

采用极化曲线、旋转圆盘电极试验和失重（质量损失）法研究了低合金钢在添加了H。o：的海水中腐蚀加速的主要影响因素。结果发现低合金钢在添加H2O2的海水中腐蚀加速主要受到了H2O2浓度、温度、搅拌速度和H2O2添加周期的影响。研究表明,搅拌速度不变、H2O2添加周期相同的条件下,在H2O2浓度为0．8mol／L的70℃海水中,低合金铜的腐蚀加速最显著;在试验的转速范围内,加速作用随搅拌速度增大变得更为显著;H2O2加入后350min内加速作用较明显。     

预腐蚀铝合金材料裂纹萌生寿命评估

铝合金在航空工业中广泛应用,因此对于铝合金构件的寿命评估很重要。利用扫描电子显微镜(SEM)原位观测技术,研究了预腐蚀铝合金试件在循环应力作用下的疲劳裂纹萌生和扩展行为。结果表明腐蚀坑对于裂纹萌生扩展行为具有强烈的影响。基于局部应变法,提出了一种预测带有腐蚀损伤的铝合金疲劳裂纹萌生寿命的评估公式。     

纳米TiO2催化臭氧化对松花江水中氨氮的影响

研究了以负载于陶粒、硅胶、沸石表面的纳米TiO₂作为催化剂时,催化臭氧化松花江水过程中氨氮浓度的变化.结果表明,在单独臭氧化过程中,氨氮浓度先升高后下降,反应30 min后的氨氮浓度与初始浓度相近.在以TiO₂/陶粒、TiO₂/硅胶为催化剂的催化臭氧化过程中,氨氮浓度也是先升高后下降,但反应过程中氨氮的平均浓度要高于单独臭氧化过程.以TiO₂/沸石为催化剂时,催化臭氧化过程中氨氮浓度先下降,然后略有升高,继而又下降,30 min时对氨氮的去除率接近80%.单独臭氧化和催化臭氧化过程中,增大臭氧投量,氨氮浓度最大值出现的时间提前,并且反应过程中氨氮浓度平均值降低.增大催化剂TiO₂/陶粒、TiO₂/硅胶的投量,催化臭氧化过程中氨氮浓度平均值升高.增大TiO₂/沸石投量,有利于氨氮的去除,但投量增大到50g以上时,对氨氮的去除效果影响很小.温度从10℃升高到30℃,对TiO₂/陶粒、TiO₂/硅胶催化臭氧化过程中氨氮浓度的变化影响不大.而以TiO₂/沸石为催化剂时,温度升高有利于催化臭氧化过程中氨氮的去除.     

V_2O_5-TiO_2离子存储电极薄膜的溶胶-凝胶法制备与性能研究

利用无机溶胶-凝胶技术制备了V2O5-（TiO2）x离子存储电极薄膜。采用X射线衍射（XRD）、原子力显微镜（AFM）、Raman光谱、循环伏安法（CV）和紫外-可见光透射光谱分别研究了复合薄膜的微观结构、化学计量、锂离子注入性能以及光学性能。结果表明复合薄膜具有V2O5的层状结构,其c轴方向的结构取向性有所降低;颗粒尺寸和表面粗糙度显著减小;同时TiO2的复合导致薄膜中V2O5的化学计量发生偏移,氧空位数量增多。当x=0.2时,薄膜具有相对较高的离子存储容量及循环稳定性,并且在离子注入/脱出状态均获得相当高的可见光透过性。     

Scale-up modeling of the twin roll casting process for AZ31 magnesium alloy

In the present study, a 2-D finite-element method (FEM) thermal-fluid-stress model has been developed and validated for the twin roll casting (TRC) of AZ31 magnesium alloy. The model was then used to quantify how the thermo-mechanical history experienced by the strip during TRC would change as the equipment was scaled up from a laboratory size (roll diameter = 355 mm) to a pilot scale (roll diameter = 600 mm) and to an industrial scale (roll diameter = 1150 mm) machine. The model predictions showed that the thermal history and solidification cooling rate experienced by the strip are not affected significantly by caster scale-up. However, the mechanical history experienced by the strip did change remarkably depending on the roll diameters. Casting with bigger rolls led to the development of higher stress levels at the strip surface. The roll separating force/mm width of strip was also predicted to increase significantly when the TRC was scaled to larger sizes. Using the model predicted results, the effect of both casting speed and roll diameter was integrated into an empirical equation to predict the exit temperature and the roll separating force for AZ31. Using this approach, a TRC process map was generated for AZ31 which included roll diameter and casting speed.     

四环素光催化降解特性与选择性研究

研究了盐酸四环素的光催化降解行为,结果表明四环素光催化降解反应符合一级反应动力学方程,吸附过程为整个光催化降解的控制步骤,推断四环素的主要降解途径是吸附在二氧化钛(TiO2)表面发生光催化氧化反应.同时,通过对四环素与磺胺甲唑或阿莫西林混合样品的降解实验表明,改变pH、TiO2投加量等因素,两种抗生素的降解表现出了明显的选择性.     

预腐蚀LY12CZ铝合金的疲劳寿命预测模型

目的研究铝合金预腐蚀疲劳的寿命评估模型。方法利用损伤力学模型,建立预腐蚀构件疲劳寿命预测模型,并利用LY12CZ铝合金进行预腐蚀疲劳的验证性实验。结果利用损伤力学建立的模型所得到的预腐蚀铝合金试件的疲劳寿命与实验结果吻合程度良好。结论基于损伤力学的铝合金预腐蚀疲劳寿命预测模型合理有效。